The first of my summer markets is less than a week away so I am a little behind in getting my schedule up.
This summer I will be at the North Shore Green Markets Friday night market on a regular basis. The dates that I have booked are:
May 1, 15 & 29
June 5 &19
July 3, 17 & 31
August 14 & 28
September 11 & 25
I now have a number of nights booked with Saturday Summer Sessions for their Saturday night concerts and artisan markets running Saturday nights in North Vancouver’s Shipbuilder’s square. The dates that I have booked with them are:
July 4 & 18
August 1, 15, 22 & 29
The August 22 market is on the same day as Slide the City so it should be and eventful day.
I now have some of my work in the Green Market Store located Across for Lonsdale Quay. This is a coop store that carries products made by many of the same vendors who attend the North Shore Green Markets Friday night market.
Wood turned Christmas ornaments are always a great item to make as the holiday season approaches. They sell well at craft fairs and any left over make great gifts for friends and family. Two types of turned Christmas ornaments that I have been making for a while now are ball ornaments and bell ornaments. This year I added ring turned ornaments as a third kind of turned Christmas ornament.
The ball ornaments that I made this year were all made from apple wood. This was mostly just because I had it available and I like the wood. These ornaments are made in three pieces with the ball being hollowed out and then finials attached to the top and bottom. In the past I have sometimes been a bit hit and miss on the finials but this year I seemed to have it dialed in from the start and I think that they are some of my best looking finials to date.
I had a special request from a family member for red ornaments in this style so I made a couple with the balls stained red and then the finials left natural.
Apparently I have given them a few ornaments over the years and red was the one colour still missing.
The next style of turned Christmas ornament that I made was done using a ring turning. For these a ring of wood was turned on the lathe with specific profiles on the inside and outside of the ring. The ring then gets cut into slices to make the ornaments. I found turning the profile on the inside of the ring to be a bit tricky and it took me a few attempts to get one that would work.
Once I had all of the slices cut out it looked like a small forest has sprouted on the table of my bandsaw.
After that the slices were cleaned up a bit and then dyed green.
And finally a topcoat of finish was added and they were strung up.
The final type of turned Christmas ornaments that I made this year were the bell ornaments. I have made these before and they are always a favourite. They are fun to make and people always like them. Basically I just use small sections of branch and shape and hollow them into a bell shape leaving a thin strip of bark at the edge. When I add the string I tie a small jingle bell to the inside so that they always have a little sound to them.
A couple of times during this past Christmas season I ran out and had to make some some more.
It is nearing the end of September as I write this and the last of the summer markets just ended which means that now it is time to start preparing for the Christmas markets.
This year I have committed to more shows than in past years as well as getting into more established shows so it is looking to be a very busy season.
November 2 – St.Thomas Aquinas Christmas Craft Fair – this is a juried show has been running for over 25 years. It is a very well established show that always draws quality vendors and a large crowd of shoppers.
November 14, 15, 16 – Shipyards Christmas Market – the North Shore Green Markets is building on the success of their Friday Night Markets in Shipbuilders square to run a Christmas market in the same location. There will be a skating rink in the square, vendors set up in the building behind the stage, food trucks and more attractions. This is running every weekend from mid-November up until Christmas and I have booked quite a few dates.
November 21, 22, 23 – West Coast Christmas Show – this is a large show put on annually in Abbotsford that features a mix of different vendors as well as presentations from local chefs. Amongst the many exhibits visitors will find holiday gifts from around the world, jewelry & accessories, toys, specialty foods, condiments, seasonings, candy/sweets along with unique and hard to find gift items both from artisans as well as unique manufacturers.
November 29, 30 – North Van Holiday Bazaar – taking over from the very successful Delbrook Christmas market that ran for many years. This show being run at Carson Graham high school on the same dates and will feature many of the same vendors that used to go to the Delbrook market.
A couple of years ago now a shot some video of a natural edge wedding goblet that I was making.
Unfortunately when I went to edit it I found that my computer at the time was simply unable to manage the files and there was really too much video to post it without being edited so it sat for a while. Now that I have a new computer I came across the video files and thought I would see what I could do with it.
As this is my first real attempt at editing video it is a little rough but here it is: The Making of a Natural edge Wedding goblet!!!
Generally wood turning in know for making wood into round shapes but other things are possible if you know how to do them, lately I had reason to make an oval handle.
What happened is that I was placing an order for some hardware that I was getting low on and decided to try out a new style of pizza cutter. When my order arrived I was surprised to see that, although there was no mention of it in the included instructions, it would be best to make the handle oval where it joined this hardware.
I haven’t made many oval handles before but I have experimented enough to know that it can be done. The way to do it involves using three different centres during the turning process. Starting with the standard centre in the middle the handle is first made round. Then the centre is moved off to one side to create the first side of the oval and then moved an equal distance to the other side of the original centre to create the other side of the oval. This is the layout sketch that I made to figure out where my three centres needed to be.
I was pretty happy with how it turned out, and on my first attempt too. Here I have already trimmed the tenon and drilled a hole for the tang on the pizza cutter so you can’t see where I placed the three centres but I just followed the sketch above. I only made the tenon and about the first two inches oval before blending it into a round shape higher up.
Test fitting the oval handle to the hardware. I think this is going to be quite a nice pizza cutter. There is a bit of figure in the maple wood used for the handle that will look good once the finishing is complete.